Description
Cross Coil
| Width – mm | Core – mm ID/OD?L |
Side Panel -mm | Lenth – lfm |
|---|---|---|---|
| 6 | 55/63/185 | cardboard 310 x 255 x 5mm | 800 -1500 |
| 10 | 55/63/185 | cardboard 310 x 255 x 5mm | 650 -1500 |
| 15 | 55/63/185 76/90/280 |
cardboard 310 x 255 x 5mm plastic 320 x 320 x 30mm |
650 – 800 800 -1500 |
| 20 | 76/90/280 | plastic 320 x 320 x 30mm | 800 – 2000 |
| 25 | 76/90280 | plastic 320 x 320 x 30mm | 800 – 1500 |
Each cross coils are individually wrapped in Polyethylene film and packed in a cardboard box.
Other widths or other packaging for flat rolls and cross coils on request.
Storablility
Originally packed in polyethylene
Min. 4 months at 30°C
Min. 8 months at 20°C
Min. 16 months at 10°C
ISOGLAS® F0710 and H0720 and H0730 should reach room temperature before opening the original packaging to prevent condensation of water on the tape.
Processing advice
When applying ISOGLAS® tape it is recommended to preheat the armature to about 110-130°C and apply a tension of about 1000 N/cm to the tape. This ensures that > 50% of the applied tension will remain in the bandage after curing and prevents a loosening of teh bandage after cooling down or in service.
After fixing the end of the tape (e.g. with a soldering iron) curing should be done according to listed curing conditions.
Detailed processing advice available on request.
Curing Conditions
To reach the optimim properties of F0710, H0720 and H0730 after application, following curing conditions is recommended.
| Temperature in °C | Time in Hours |
|---|---|
| 120 | 24 |
| 135 | 4 |
| 150 | 1.5 |
| 165 | 1 |
* The curing time refers to the time after reaching the curing temperature.
| Technical Data | ||||||
|---|---|---|---|---|---|---|
| Type | F0710 | H0720 | H0730 | |||
| Properties | Test Method | Unit | Value | Value | Value | Value |
| Nominal Thickness | IPV 020 | mm | 0.30 | 0.20 | 0.30 | 0.30 |
| Tolerance | IPV 020 | mm | ±0.03 | ±0.02 | ±0.03 | ±0.03 |
| Total Substance | IPV 004 | g/m² | 544 ± 30 | 392 ± 18 | 544 ± 30 | 583 ± 30 |
| Resin Content | IPV 018 | % | 25 ± 2 | 30 ± 25 | 25 ± 2 | 30 ± 3 |
| Glass yarns per cm width | IPV 023 | 30 ± 1 | 40 ± 1 | 30 ± 1 | 30 ± 1 | |
| Tensile strength in B-stage | IPV 080 | N/10mm | ≥ 2000 | ≥ 1000 | ≥ 2000 | ≥ 2000 |
| Tensile Strength after curing (3h at 160°C) at 23°C / 155°C |
IPV 080 | N/10mm | ≥ 2500/ ≥ 2000 |
≥ 1200/ ≥ 1000 | ≥ 2500/ ≥ 2000 |
≥ 2500/ ≥ 2000 |
| Elongation | IPV 080 | % | 1 – 3 | 1 – 3 | 1 – 3 | 1 – 3 |
| Flexural strength after curing (3h at160°C) |
IPV 083 | N/mm² | ≥ 1200 | ≥ 500 | ≥ 1200 | ≥ 1200 |
| Reduction of flexural strength after 28 days immersion into boiling water | IPV 083 | % | ≤50 | ≤50 | ≤50 | ≤50 |
| Modulus of elasticity | ISO 178 | N/mm² | approx. 50.000 | approx. 50.000 | approx. 50.000 | approx. 50.000 |
| Tracking resitance | IEC60112 | CTI | 600(M) | 600(M) | 600(M) | 600(M) |
| Thermal Classification | IEC60216 | °C | 155(F) | 180(F) | 180(F) | 180(F) |
